California customers can get faster delivery by ordering from

Cryo-Fog LP

ITEM # CF-0401 Categories: | |

The Cryo-Fog LP is a powerful 1700 Watt low fog generator with fogger and cooling chamber all built in to a road case that’s only 26″ x 20″ and 12″ tall! It uses Cryo-Fog Fluid to make dense white fog and requires a low pressure dewar tank of liquid CO2 (available from any gas company) to chill the fog and cause it to lay low. It can be controlled with 3 channels of DMX – 1 for fog output, 1 for temperature, and 1 for fan – and each parameter can be variably adjusted from 1-100%.  This allows you to create thin fog that creeps across the floor, billowing clouds that look like ocean waves, or anything in between. It comes with 5L of Cryo-Fog Fluid and a 5m hose for connecting a dewar of CO2. Low pressure dewar tanks hold an average of 400 lbs of liquid CO2 and are recommend when need a lot of low fog, for a permanent installation or long running show. For short and/or portable productions, the CryoFog HP is recommended instead, as high pressure tanks are much smaller, and the ease of use outweighs the higher cost per lb. of CO2.





Related products:


The Cryo-Fog LP is a powerful low fog machine. It has the option of either 2200W of output at 220V or 1500W of output at 110V. The Cryo-Fog LP is a fog generator, a fan and a cooling chamber built into a compact flightcase (67 x 51 x 30 cm) with space next to the fog gene- rator to held a 5ltr can of fluid. Liquid CO2 is used to cool down the fog of the inbuilt low temperature fog generator. Therefore the machine produce thick low fog which distributes evenly. The machine is powerful enough to fill even big stages with low fog within a short time. The liquid CO2 is delivered from a low pressure tank (20 – 24 bar), which is connected to the machine via a hose. The intelligent technology ensures sure that the fogging process will not start before the cooling chamber has reached the right temperature. As a result, no “warm” fog – which will go upwards – can escape from the machine. The Cryo-Fog LP benefits from its compact size, the low weight, the powerful output, the low noise and the easy operation. This particular Cryo-Fog machine is a Low Pressure system.


DMX 512 as standard

  • The Cryo-Fog LP can be controlled via DMX 512. The machine uses three channels on the desk. So, the pump, the fan and also the CO2-valve can be adjusted separately. If the Cryo-Fog is controlled via DMX, the machine can also be used as a “normal” fog generator. The DMX start address can be adjusted and saved via the control panel.
  • The machine can also be controlled with analogue (0 – 10 V) via a lighting desk or via XLR-remote (option). The fogging process starts automatically as soon as the cooling chamber has reached the right temperature.
  • A stand-alone-mode is also possible. The adjust- ment of the pump is done directly at the machine. The fan runs automatically. A short press at the start button makes the machine run and the fogging process start as soon as the cooling cham- ber has reached the right temperature. Therefore to keep the start button pressed permanently is unnecessary.

Control panel
The control panel with LED-display has simple symbols to allow for easy operation. It also protects the control buttons against dirt.

Fine adjustments of the output
Digital technology makes fine adjustment of the pump possible. In steps of 1% the output can be adjusted from 0 – 99%. Thus, any desired effect from a tiny fog-cloud to the thickest fog can be produced. This enables the Cryo-Fog to be used in both small and large locations.


Special Cryo Fluid is needed to run the Cryo-Fog LP.

Manual | Download
Specsheet | Download
Fluid MSDS | Download
CO2 MSDS | Download
CO2 Information Sheet | Download
Output Measurement | Download

Additional information

Shipping Weight 62 lbs
Shipping Dimensions 27 × 21 × 13 in

120V (default), 230V (special order)

Related products: